TM 5-6115-332-14 P-8-614-14 TO  35C2-3-424-1 (20) Remove screw and washers securing the blower fan and remove blower fan. (21) Remove the ground strap. (22) Remove screws and washers which secure the generator housing to the support brackets. ring NOTE Block  up  engine  with  suitable  cribbing  before  re- moving  screws  and  lockwashers  securing  the  gener- ator to the flywheel housing. Attach a suitable sling around the generator housing and with a hoist raise housing until a slight tension is felt. (23) Remove the screws and lockwashers secu- the generator to the flywheel housing. (24) Shale generator housing to the rear and remove  the  housing.  Remove  air  inlet  grille  from housing. (25) Straighten tang on locks and remove the screws  and  locks  securing  the  drive  disk  to  the adapter and remove drive disk and rotor. (26)   Straighten   tang   on   locks   and   remove screws  and  locks  securing  the  adapter  to  the  fly- wheel and remove adapter from the flywheel. b. Installation. (1)  Position  adapter  in  place  on  the  flywheel and secure with locks and screws. NOTE Bend tang up over screws. (2)  Position  the  drive  disk  in  place  on  the adapter and secure with locks and screws. (3) housing NOTE Bend tang up over screws. Place air inlet grille around the generator and  secure  housing  and  grille  to  the  fly- wheel housing with lockwashers and screws. NOTE Torque  screws  to  13  to  16  FT.  LB.  (1.80  to  2.21 kgm). (4) Install the ground strap. (5)  Position  blower  fan  in  place  and  secure with washers and screws. NOTE Torque  screws  to  14  to  16  FT.  LB.  (1.94  to  2.21 kgm). (6) Install the fan cover to the generator hous- ing with washers and screws. (7) Reconnect electrical cable to generator. (8)  Position  the  control  box  in  place  on  the bottom  resilient  mounts  and  secure  with  washers and  screws. (9)  Secure  the  control  box  to  the  generator housing with washers and screws. (10) Install ground strap. (11)   Reconnect   electrical   cables   to   control box. (12) Position the control box bracket in place and secure to the top of the generator housing with washers and screws. (13)  Install  lifting  eye. (14)  Secure  bracket  to  side  of  the  generator housing with washers and screws. (15)  Install  resilient  mounts  to  control  box bracket with screws, washers, and nuts. (16) Place toolbox in position and secure with screws, lockwashers, and nuts. (17) Place guard frame over generator set and secure  to  the  flywheel  housing  with  screws,  lock- washers, and nuts. (18)   Secure   guard   frame   to   the   skid   base using screws, lockwashers, and nuts. (19) Place battery in battery frame and posi- tion hook bolt in place. (20) Install upper battery frame with washers and  nuts. (21) Reconnect battery cables. (22) Place fuel can in fuel can bracket and se- cure with strap. Depress clamp to secure. (23) Place fuel can adapter in fuel can and se- cure by depressing the locking handle. 6-3.  Generator  (Model  MEP-022A) a. Removal. (1)  Lift  the  locking  handle  (fig.  3-4)  and  re- move the fuel can adapter from the fuel can. (2)  Lift  clamp  and  loosen  the  strap  securing the  fuel  can  in  the  fuel  can  bracket  sufficiently  to allow for removal of the fuel can. (3) Disconnect the battery cables (fig. 4-22). (4)  Remove  nuts  and  washers  which  secure the  upper  battery  frame  and  remove  frame  and hook bolts. (5) Remove battery from battery frame. (6) Remove the nuts, lockwashers and screws (fig. 4-33) that secure the guard frame to the skid base. (7) Remove the screw and lockwasher that se- cures the guard frame to the flywheel housing and remove guard frame from the generator. 6-4