TM 5-6115-405-15
Fuel tank capacity ..................... 18 oz liquid
The output is taken from the stator and wired directly to
Piston displacement .................. 3.3 cu in.
the output connector. The output is 12.5 watts at unity
Bore .......................................... 1 3/4 in.
power factor.
Stroke ....................................... 1 3/8 in.
d. Carrying Case. The entire generator set and the
Compression ratio ..................... 8:1
included accessories are provided with a specially
Air cleaner.................................Dry type
designed molded plastic carrying case (fig. 1-3) for
Ignition system .......................... Magneto
Type of lubrication.....................Oil mixed with fuel
transportation and storage. The upper half of the case
Governor................................... Mechanical-centrifugal
has a carrying handle on top and a storage area for the
type
publications case which is secured by a spring clip. An
(3) Generator.
air valve is provided to equalize inside and outside air
Manufacturer............................. Homelite
pressures. (See instructions on carrying case.) The
Type.......................................... Permanent magnet
upper half of the case is secured to the lower half by
Rated speed..............................4000 rpm
four latches. An accessory bag is placed in the lower
Drive ......................................... Direct
portion of the case.
Phase........................................ Single
Output power ............................ 125 watts
Output voltage .......................... 115 volts, 400 cps
1-4. Identification and Tabulated Data
Power factor..............................1.0
a. Identification.
The
Homelite
Model
(4) Engine accessories.
XLA11/1/400-1P generator set has two major
(a) Carburetor.
identification plates One is located on the carrying case
Manufacturer............................. Tillotson
and the other is located on the starter fan housing. The
Model ........................................ HS40A
information contained on the two plates is listed below
Type.......................................... Diaphragm with integral
and is identical except the serial number is not included
fuel pump
on the carrying case identification plate.
(b) Ignition System.
Type.......................................... Magneto
Generator set
Manufacturer of magneto .......... Wico
0.125 KW
Model ........................................ FW-2782-C
115 V
Manufacturer of high ................. Hallet
1 PH
tension lead.
100 CYC
Type.......................................... Shielded
1.0 PF
(c) Spark plug.
2 WIRE
Manufacturer............................. Champion
4000 RPM
Type.......................................... XEJ-12 with integral
suppresser
Fuel: Gasoline -- Oil mixed
Size .......................................... 14 mm
Model No. XLAll5/l/400-1P
(5) Adjustment data.
Contract No. DA23-195-AMC-00763(T)
Spark plug gap..........................0.030 in.
FSN 611930-9498
Magneto breaker point
0.015 in.
gap
b. Tabulated Data.
(6) Torque data.
Spark plug............................... .250-300 in lb
(1) Generation, set.
No. 8 spinlock screws................36 in. lb min
Manufacturer.............................Homelite
No. 10 spinlock screws..............50 in. lb min
Model ........................................ XLA15/1/400-1P
No. 12 spinlock screws..............80 in. lb min
(2) Engine.
No. 4-40 ordinary screws...........4-3/4 in. lb min
Manufacturer............................. Homelite
No. 6-32 ordinary ...................... 8-3/4 in. lb min
screws.
Type.......................................... Air-cooled
No. 832 ordinary........................18 in. lb min
Number of cylinders .................. 1
screws.
Stroke cycle .............................. 2
No. 10-24 ordinary .................... 23 in. lb min
Fuel .......................................... Gasoline and oil mixed
screws.
No. 10-32 ordinary .................... 32 in. lb min
screws.
1-2
